Pre Trip Inspection Class B Passenger Bus Checklist

Frame is not bbc, securely mounted. It helps bus drivers or bus fleet supervisors to catch mechanical issues, defects, and damages.

The "PreTrip Inspection" is a crucial component in the

Apply parking brake only and shift into a lower gear.

Pre trip inspection class b passenger bus checklist. Here are some benefits of using a school bus:1. Apply full pressure to the brake pedal, hold down for about one minute, and watch for the needle to stabilize. not bent or damaged lights & reflectors:

John checks underneath and around the bus for cracks or imperfections. Valve caps and stems are not missing, broken or damaged. This template has been built to perform the following:

The school bus instructor for this video is john vezaldenos, a california certified state instructor. You must name and point to or touch each item, and fully explain what you are inspecting (you must ensure the. The air pressure should be stable.

Battery/ belts/ hoses/ wiring 2. Clearance lights proper color, securely mounted, not cracked or dirty, no moisture inside lense. Make sure your air pressure does not lose many more than 2 psi in one minute.

Identify all defects or you may not receive credit. Driver seat, passenger seats, padding, interior, and floor condition. Not bbc, no holes, all rivets in place.

Gently pull against the brake by releasing the clutch, and it should hold the vehicle. Look for dripping fluids on the underside of the engine and transmission. mounted properly not missing, ripped or torn dot bumper:

2) no recapped, retreaded or regrooved tires allowed on the front of the bus. So you need to have it down. 5 under bus leaks (oil, fuel, coolant, water, power steering filled, brake fluid, etc.

Ive been working on this for a long time and. John sets chocks to make sure bus is secure during inspection. Tell the tester how you know that the part you are 1 inspecting is in good, safe working condition.

Applying for a p or s endorsement. No uid leaks beneath the van are visible van sits level with no sign of uneven loading all exterior lights/signal turns operate correctly windshield, windows, and exterior mirrors are all. not bent, broken, or damaged close and latch securely hinges secure, no damage splash guards:

The content of this video relates to basic safety rules around school buses. 3) no cuts or damage to the sidewall or tire tread. A yes indicates the item is acceptable.

Look for puddles on the ground that would indicate a leak. It keeps kids more active. For children who are going to be sitting down in the classroom for most of the day, this helps them to do more physical activities.

Each of the 20 questions is based on the official 2021 cdl manual. 1) 4/32 minimum tread depth in the major grooves. Taking the bus to school involves walking to the bus stop.

There are several answer options, but only one of them is. Do the same check on the passenger side. Bus maintenance & safety inspection.

With the engine running, apply the foot brake and hold for five seconds. A bus driver must have a passenger endorsement on his/her cdl. To obtain the endorsement, you must pass a knowledge test on sections 2 and 4 of this manual (if the bus has air brakes, you also must pass a knowledge test on section 5).

Check for leaks, condition of hoses. Rear of the truck doors: John enters the bus to begin the first phase of the pre trip inspection.

Before opening the hood, check for leaks under the engine. 6 general outside appearance b check under the hood 1. You also must pass the skills tests required for the class of vehicle you drive.

Left side rear right side front 1. The following steps would be applicable to the inspection of a school bus, starting at the engine compartment and following a clockwise direction around the vehicle. At minimum, the inspection must include the brakes, steering, lights and reflectors, tires, horn, windshield wipers, mirrors, coupling devices, wheels and rims, emergency equipment and load security.

Dot tape is securely mounted, not dirty, covers at least 50% of the side. Header board not bbc, all hardware present.

Pin by Bernardo Cdltexas on CDL Pretrip Inspection tips